ADI公司的ADuCRF101是全集成無線數據采集系統,集成了12位SAR ADC,低功耗ARM Cortex™-M3處理器, 862 MHz- 928 MHz 和431 MHz- 464 MHz RF收發器以及閃存/EE存儲器,包括UART, I2C, SPI, GPIO端口和PWM在內的外設,主要用在無線傳感器,遠程醫療系統,工業和家庭自動化,財產跟蹤,安全系統以及醫療保健設備等.本文介紹了ADuCRF101主要特性和優勢,框圖, ADuCRF101迷你評估板主要特性,電路圖和PCB元件布局圖.
The ADuCRF101 is a fully integrated, data acquisition solution that is designed for low power, wireless applications. It features a 12-bit analog-to-digital converter (ADC), a low power ARM Cortex™-M3 processor, a 862 MHz to 928 MHz and 431 MHz to 464 MHz RF transceiver, and Flash®/EE memory. The ADuCRF101 is packaged in a 9 mm × 9 mm LFCSP.
The data acquisition section consists of a 12-bit SAR ADC. The six inputs can be configured in single-ended or differential mode. When configured in single-ended mode, they can be used for ratiometric measurements on sensors that are powered, when required, from the internal low dropout regulator (LDO). An internal battery monitor channel and an on-chip tempera-ture sensor are also available.
This wireless data acquisition system is designed to operate in battery-powered applications where low power is critical. The device can be configured in normal operating mode or different low power modes under direct program control. In flexi mode, any peripheral can wake up the device and operate it. In hibernate mode, the internal wake-up timer remains active. In shutdown mode, only an external interrupt can wake up the device.
The ADuCRF101 integrates a low power ARM Cortex-M3 processor. It is a 32-bit RISC machine, offering up to 1.25 DMIPS peak performance. The ARM Cortex-M3 processor also has a flexible 14-channel direct memory access (DMA) controller that supports communication peripherals, serial peripheral interface (SPI), UART, and I2C. Also provided on chip are 128 kB of nonvolatile Flash/EE memory and 16 kB of SRAM.
A 16 MHz on-chip oscillator generates the system clock. This clock can be internally divided for the processor to operate at a lower frequency, thus saving power. A low power, internal 32 kHz oscillator is available and can be used to clock the four timers, as follows: two general-purpose timers, a wake-up timer, and a system watchdog timer.
A range of communication peripherals can be configured, as required, in a specific application. These peripherals include UART, I2C, SPI, GPIO ports, PWM, and RF transceivers.
The RF transceiver communicates in the 862 MHz to 928 MHz and 431 MHz to 464 MHz frequency bands using multiple configurations.
On-chip factory firmware supports in-circuit serial download via the UART, and nonintrusive emulation and program download are also supported via the serial wire interface. These features are incorporated into a low cost development system supporting this precision analog microcontroller family.
The ADuCRF101 operates from 2.2 V to 3.6 V and is specified over an industrial temperature range of −40°C to +85°C. It is available in a 64-lead LFCSP package
ADuCRF101應用:
Battery powered wireless sensor
Medical telemetry systems
Industrial and home automation
Asset tracking
Security systems (access systems)
Health and fitness applications
ADuCRF101主要特性和優勢:
Analog I/O
6-Channel 12-bit SAR ADC
Single-ended and differential inputs
Programmable data rate up to 167 kSPS
On-chip voltage reference
Supply rante: 2.2V to 3.6V
Power Consumption
280 nA, in power-down mode, nonretained state
1.9 µA, in power-down mode, processor memory and transceiver memory retained
210 µA/Mhz, Cortex-M3 in active mode
12.8 mA transceiver in receive mode, Cortex-M3 in power-down mode
9 mA to 32 mA transceiver in transmit mode, Cortex-M3 in power-down mode
RF Transceiver
Frequency bands, 862 MHz to 928 MHz and 431 MHz to 464 MHz
Multiple Configurations supported
Receiver sensitivity (BER), −107.5 dBm at 38.4 kbps, 2FSK
Single and ended and differential PA
Low external BOM
Microcontroller
32-bit ARM Cortex-M3 processor
Serial Wire download and debug
External Watch crystal for wakeup timer
16 MHz internal Oscillator with 8-way Programmable Divider
Memory 128 kB Flash/EE memory, 16 kB SRAM
10,000-cycle Flash/EE endurance
10-year Flash/EE retention
In-circuit download via serial wire and UART
On-Chip Peripherals
UART, I2C and SPI Serial I/O
28-pin GPIO port
2 general-purpose, 16-bit timers
32-bit wake-up timer
16-bit watchdog timer
8-channel pulse-width modulation (PWM)
Package
64-lead, 9 mm × 9 mm LFCSP
Temperature range: −40°C to +85°C
Tools
Low cost development system
Third-party compiler and emulator tool support
圖1. ADuCRF101功能框圖
ADuCRF101迷你評估板
The ADuCRF101 is a fully integrated data acquisition solution designed for low power wireless applications. It features a 12-bit ADC, a low power ARM Cortex™-M3 processor, a 431MHz to 464 MHz and 862 MHz to 928 MHz RF transceiver, and Flash/EE memory, in a 9 mm × 9 mm LFCSP package.
The ADuCRF101 mini board allows a user to program, debug and evaluate the performance of the ADuCRF101. Its small form factor makes it the ideal hardware for evaluation of large wireless sensor network.
Different hardware kits are available, from a mini board on its own, to a combination of emulator and boards.
Software Contents:
Keil MDKARM evaluation version integrated software development tool.
IAR EWARM evaluation version integrated software development tool.
CM3WSD Serial Downloader
Example Code
Function Libraries
Get Started User Guide
Datasheets, Application Notes, Etc
圖2. ADuCRF101迷你評估板外形圖
圖3. ADuCRF101迷你評估板電路圖(1)
圖4. ADuCRF101迷你評估板電路圖(2)
圖5. ADuCRF101迷你評估板電路圖(3)
圖6. ADuCRF101迷你評估板PCB元件布局圖:頂層
圖7. ADuCRF101迷你評估板PCB元件布局圖:底層
詳情請見:
http://www.analog.com/static/imported-files/data_sheets/ADuCRF101.pdf
和http://www.analog.com/static/imported-files/eval_boards/Eval_ADuCRF_Schematic.pdf
