《電子技術應用》
您所在的位置:首頁 > 電源技術 > 解決方案 > PowerintLNK457DG7WB10LED燈電源方案(DER324)

PowerintLNK457DG7WB10LED燈電源方案(DER324)

2012-04-12
作者:Powerint公司
</a>LED" title="LED">LED" title="LED">LED燈電源采用LinkSwitch-PL系列的LNK457DG,,具有單級PFC和精確的恒流(CC)輸出以及低成本元件少與小尺寸的特點,,AC輸入電壓90V-132V,115VAC時的效率大于90%,,PF大于0.95,,集成了無負載檢測/短路保護,熱關斷自動恢復,,可替代B10白熾燈,。本文介紹了LinkSwitch-PL系列產品亮點,方框圖,典型應用電路以及7W PFC LED驅動器指標,,電路圖,,材料清單和PCB布局圖。

The LinkSwitch-PL family enables a very small and low cost single-stage power factor corrected constant current driver for solid state lighting. Optimized for direct LED current sensing, the LinkSwitch-PL operates over a wide input voltage range delivering an output power of up to 16 W. The LinkSwitch-PL control algorithm provides flicker-free TRIAC dimming with minimal external components.

Each device incorporates a 725 V rated power MOSFET, a novel discontinuous mode variable frequency variable on-time controller, frequency jitter, cycle by cycle current limit and hysteretic thermal shutdown in a monolithic 4-pin IC, available in SO-8C, eSOP-12, and eDIP-12 packages.

LinkSwitch-PL系列產品亮點:

Dramatically Simplifies Off-line LED Drivers

• Flicker-free phase-controlled TRIAC dimming

• Single stage power factor correction and accurate constant current (CC) output

• Very low component count with small non-electrolytic bulk capacitor for compact replacement lamp designs

• Compact SO8, eSOP, and eDIP packages

• Completely eliminates control loop compensation

Advanced Performance Features

• Optimized for non-isolated flyback designs

• Frequency jitter greatly reduces EMI filter size and costs

• Low dissipation direct sensing of LED current

Advanced Protection and Safety Features

• Cycle skipping regulation for abnormally low output power to clamp peak output current delivered

• 725 V integrated power MOSFET allows small bulk capacitance and maximizes power capability

• Short-circuit, overload, open feedback and output overvoltage protection

• Hysteretic thermal shutdown

• Meets high-voltage creepage between DRAIN and all other pins both on PCB and at package EcoSmart™ - Energy Efficient

• High power factor optimizes system lumen per input VA

• Control algorithm balances switching and conduction losses over line and load to maintain optimum efficiency

圖1,。LinkSwitch-PL系列功能方框圖

圖2,。LinkSwitch-PL系列典型應用電路圖

圖3。采用LinkSwitch-PL系列的替代A19白熾燈的5W 15V LED驅動器電路圖

采用LinkSwitchTM-PL系列LNK457DG的替代B10燈的7W PFC LED驅動器

This document is an engineering report describing a non-isolated LED driver (power supply) utilizing a LNK457DG from the LinkSwitch-PL family of devices.

The DER-324 provides a single 7 W constant current output.

The key design goals were high efficiency to maximize efficacy and small size. This allowed the driver to fit into B10 sized lamps and be as close to a production design as possible.

The board was optimized to operate over the low AC input voltage range (90 VAC to 132 VAC, 47 Hz to 63 Hz). LinkSwitch-PL IC based designs provide a high power factor (>0.95) meeting current international requirements.

The form factor of the board was chosen to meet the requirements for standard B10 LED replacement lamps. The output is non-isolated and requires the mechanical design of the enclosure to isolate the output of the supply and the LED load from the user.

7W PFC LED驅動器主要特性:

? Single-stage power factor corrected and accurate constant current (CC) output

? Low cost, low component count and small PCB footprint solution

? Highly energy efficient, >90 % at 115 VAC input

? No potting is needed to operate at 75 ºC internal case ambient.

? Fast start-up time (<50 ms) – no perceptible delay

? Integrated protection and reliability features

? No-load protection / hard short-circuit protected

? Auto-recovering thermal shutdown with large hysteresis protects both components and PCB

? No damage during line brown-out or brown-in conditions

? PF >0.95 at 115 VAC

? %A THD <25% at 115 VAC

? Meets IEC 2.5 kV ring wave, 500 V differential line surge and EN55015 conducted EMI

圖4,。7W PFC LED驅動器PCB外形圖(頂視圖)

圖5,。安裝在B10燈罩內的PCB外形圖
7W PFC LED驅動器指標:


圖6。230 V / 30 mA 替代燈電路圖
230 V / 30 mA 替代燈材料清單:


圖7,。7W PFC LED驅動器PCB元件布局圖(頂層)

圖8,。7W PFC LED驅動器PCB元件布局圖(底層)
詳情請見:
http://www.powerint.com/sites/default/files/PDFFiles/der324.pdf



本站內容除特別聲明的原創文章之外,轉載內容只為傳遞更多信息,,并不代表本網站贊同其觀點,。轉載的所有的文章、圖片,、音/視頻文件等資料的版權歸版權所有權人所有,。本站采用的非本站原創文章及圖片等內容無法一一聯系確認版權者。如涉及作品內容,、版權和其它問題,,請及時通過電子郵件或電話通知我們,以便迅速采取適當措施,,避免給雙方造成不必要的經濟損失,。聯系電話:010-82306118;郵箱:[email protected],。